next up previous contents index
Next: Terminal Devices Up: The Side Menu: Geometry Previous: The deck Button: Save   Contents   Index


The devs Button: Device Menu

\epsfbox{devs.eps}

The devs button appears only in electrical mode, and pressing this button will toggle the display of the device selection menu.

There are three styles of the device menu. The default style contains a menu bar with four entries: Devices, Sources, Macros, and Terminals. Each brings up a sub-menu containing names of library ``devices'', that fall into each category.

The second menu style is similar, but the menu bar contains the first letter of the device name (not the SPICE key).

In either of these styles, pressing and holding button 1 while the pointer is over one of the menu bar buttons will pop up a menu of device names. Moving the pointer down the menu will highlight the entry under the pointer. A selection can be made by releasing the button.

The third style is the pictorial menu, which displays the schematic symbol of each available device, in alphabetical order. Clicking on one of the device images will establish the selection.

Each menu style contains a button from which the style can be cycled.

After a selection is made, the device symbol will be ghost-drawn and attached to the pointer, and the device will be placed at positions where the user clicks in the drawing windows. The device is positioned such that the reference terminal is located at the point where the user clicked. Devices are placed according to the current transform, which is defined from the pop-up produced by the xform button in the side menu.

The devices available and other details depend upon the definitions in the device library file. By default, this file is named ``device.lib'', and is located in the installation startup directory, but this can be superseded by a custom file of the same name which is found in the library search path ahead of the default file.

The present device menu style tracks, and is tracked by, the DevMenuStyle variable. This variable can be set (with the !set command) to an integer 0-2. If 0 or unset, the categorized layout is used. If 1, the alphabetized variation is used, and 2 specifies the pictorial menu. This variable tracks the style of the menu, and resets the style when set.

The following table lists the devices found in the device library file supplied with Xic.

Name Description
Contact Devices
gnd Ground Contact
gnde Alternative Ground Contact
tbar Contact Terminal
tblk Alternative Contact Terminal
tbus Bus Contact Terminal
SPICE Devices
res Resistor
cap Capacitor
ind Inductor
mut Mutual Inductor
isrc Current Source
vsrc Voltage Source
dio Junction Diode
jj Josephson Junction
npn NPN Bipolar Transistor
pnp PNP Bipolar Transistor
njf N-Channel Junction FET
pjf P-Channel Junction FET
nmos1 N-Channel MOSFET, 4 Nodes
pmos1 P-Channel MOSFET, 4 Nodes
nmos N-Channel MOSFET, 3 Nodes
pmos P-Channel MOSFET, 3 Nodes
nmes N-Channel MESFET
pmes P-Channel MESFET
tra Transmission Line
ltra Transmission Line (LTRA Compatible)
urc Uniform RC Line
vccs Voltage-Controlled Current Source
vcvs Voltage-Controlled Voltage Source
cccs Current-Controlled Current Source
ccvs Current-Controlled Voltage Source
sw Voltage-Controlled Switch
csw Current-Controlled Switch
Misc.
opamp Example Macro
vp Current Meter

The colors used in the pictorial device menu can be changed by setting the Special GUI Colors (see A.8.3) listed below. This can be done in the technology file, or with the !setcolor command.

variable purpose default
GUIcolorDvBg background gray90
GUIcolorDvFg foreground black
GUIcolorDvHl highlight blue
GUIcolorDvSl selection gray80



Subsections
next up previous contents index
Next: Terminal Devices Up: The Side Menu: Geometry Previous: The deck Button: Save   Contents   Index
Stephen R. Whiteley 2017-03-22